1、長度。登車橋http://www.qdcbgg.com/一般全長10米左右，根據噸位的不同，承載重量不同，6噸的10500mm,8噸的11200米、10噸的11300米，非常適合在露天空場的地面擺放使用。
Ramps are generally about a total length of 10 meters, depending on the tonnage, carries a different weight, 6 tons of 10500mm, 8 11200 m tons, 10 tons of 11,300 meters, ideal for placing ground exposed sky field use.

2、坡度。登車橋自身必須有一定的坡度才能使叉車駛入車廂內進行貨物裝卸坡度長度也有所不一，有坡度上為7000mm、7500mm、8000mm不等，主要考慮安全性和使用的穩定性。
Ramps itself must have a certain slope in order to make the truck into the inside slope length cargo handling has also been mixed, there is a gradient of 7000mm, 7500mm, 8000mm range, the main consideration the safety and stability.

3、寬度。登車橋還必須有一定的自身寬度，如何寬度太小不利于叉車行駛裝卸貨物，寬度太大則有占據一定空間，大可不必。所以一個合理的寬度是很必要的，通常情況下登車橋的寬度為1800mm，2000mm，2100mm。而登車橋寬度則分內寬與總寬，內寬我們已經說過是通道寬度，總寬主要是兩邊的護欄的寬度加上通道寬度。
Ramps must also have a certain degree of self-width, the width is too small is not conducive to driving the truck loading and unloading, the width is too large to occupy some space there, no need. So a reasonable width is necessary,usually Ramps width of 1800mm, 2000mm, 2100mm. Ramps and wide since the beginning of the total width of the wide, wide as we have said is the channel width, the total width of both sides of the main channel width plus the width of the fence.

4、高度。升高高度作為登車橋最為重要的一項，高度可根據貨物的車輛不同，進行高低調節使之能夠與車廂臺面持平進行批量裝卸貨物。由于不同廠家生產的登車橋，設計制造臺面高度最高與地面距離也有所不同，有離地面1000mm,1200mm。通過液壓升高行程高度有300mm、400mm、600mm不等，登車橋自身高度加上行程高度最高高度為1800mm幾乎所有貨運車輛都可以滿足。
Ramps highly elevated as the most important one, according to the vehicle height is different goods, the level of regulation so that it can carry on with the car flat mesa bulk cargo handling. Because different manufacturers Ramps, design and manufacture the highest table height and distance from the ground are different, there is ground 1000mm, 1200mm. By increasing the stroke hydraulic height 300mm, 400mm, 600mm, ranging Ramps own height plus the height of the maximum height of 1800mm stroke almost all freight vehicles have to meet.

5、操作度。操作登車橋http://www.qdcbgg.com/上升下降，可以使用兩種操作方法，一種手動泵站，采用手搖液壓起升，勞動程度大，有些費力。可以在任何情況下操作使用。采用電動液壓起升下降，勞動強度減弱，省力。一旦斷電將無法使用，但是現在已經出現手動與電動兩用的登車橋，更為方便使用。
Operating Ramps rise and fall, you can use two methods of operation, a manual pump stations, using hand-hydraulic lifting, labor-degree, and some effort. Can operate under any circumstances use. Decrease the use of electro-hydraulic lifting, labor intensity decreased, and effort. Once the power failure will not be used, but now there have been manual and electric dual-Ramps, more convenient to use.